Choose UEFI: CD/DVD Drive * This option only shows on Windows7 64bit and Vista 64bit OS.Step 15: Follow Windows Installation Guide to install OS.Model=DN2800MT&cat=Download&os=BIOSAnswer: You may follow the steps below: 1. (Refer the picture) #sudo apt-get update #sudo apt-get install ethtool #sudo ethtool –s eth0 wol g #sudo reboot 5. Answer: There are various possibilities that cause this issue, please refer to the following suggestions to check your system. Please make sure your HDDs' SATA power cable and SATA cable are connected with the motherboard. Enter the BIOS setup screen, scroll to the advanced page and enter Storage Configuration, set SATA mode to [IDE].
Answer: Since the v BIOS requires different settings for Windows 7, you might see such symptoms during booting.
Please flash the corresponding BIOS version for your system from our website: https:// Please install ethtool to enable WOL by following command. Adjust the DVI function option to [as HDMI] in BIOS\Advanced\North Bridge Configuration. Set HDMI as default playback device in Control Panel\Sound.
Step 6: Key in "drvcfg –s [Drv number] [Ctrl number]" to enter Raid Utility.
For example: key in "drvcfg –s 4E B5" Step 7: Choose [Logical Drive Main Menu] to set up Raid Drive.
Answer: Please update the latest BIOS from ASRock official website firstly. cat=BIOS Because of AM4 memory compatibility issue, some high frequency memory modules may not work with XMP profile successfully.
And the monitor will show Secure Backup UEFI (B--Answer: If you have a TPM module on the motherboard and want to update BIOS, please follow the steps below to disable TPM function before flashing BIOS. Also keep the default UEFI setting of "Dual Graphics" option on [Auto].Step 3: Press F11 during boot up and choose boot to [Built-in EFI Shell].Step 4: Key in "drvcfg", and you will see the information like below: Drv[4E] Ctrl[B5] Lang[eng] Step 5: Key in "dh [Drv number]", for example: key in "dh 4E".Copy the BIOS file to your USB flash drive and extract BIOS file from the zip file. Rename the file to "creative.rom” and put the file on root directory Step 6. Answer: To support Intel Optane Memory, please make sure if your system meet the followings: 1. When booting properly, the system works on the active BIOS_A1 as picture below. Left-click Question (Q&A-123|409): After installing the onboard VGA driver on my 100 series platform with Windows 10, the system keeps on blinking and pops up "Graphics driver stopped responding and has recovered". (2/1/2016) Question (Q&A-122|404): Under Windows 10 version 1511 (Threshold 2 Build 10586), Z170 Extreme6 and Z170 Gaming K6 series models may not resume from Sleep mode (S3) or enter into Hibernation mode (S4) properly.(12/1/2015)Answer: For Intel G3258 CPUs to support Windows 10, please download the following BIOS or later versions with Microcode 19 from the download links on our website. cat=Beta Z87-M8 P1.70 or later versions Link: https:// Series/? Un-install Intel® Smart Connect Technology driver from your system. Please remove all unnecessary PCI-E devices including 1 R9 295x2 VGA card, and only install one VGA card onto the system as a display output. Question (Q&A-116|391): If I install two monitors (DVI and D-sub) on FM2A88X Extreme6 and boot up the system, the system will freeze during Windows 8.1 booting process. (3/1/2015)Answer: Please check whether the BIOS option "APCI HPET table" is enabled, or please disable "Systeminfo Scan" in 3Dmark.Install the 24 pin power connector to the motherboard. Choose Z270, H270 or B250 series platform and 7th Generation (Kaby Lake) Intel® Core™ Processor. However, if the active BIOS_A1 is corrupted or damaged, after several failed boot attempts, it will automatically do BIOS recovery from the backup BIOS_B1 and then the system will still work on the active BIOS_A1. If your model isn't listed in the table, please visit the beta zone of your model and then update the latest beta BIOS. For more suggestions about 3Dmark, please refer to 3Dmark FAQ: Answer: Step 1: Please make sure that you have installed the latest BIOS and two 1866MHz or higher frequency memory modules in dual channel.Download Link: https://downloadcenter.intel.com/product/128199/Graphics-for-8th-Generation-Intel-Processors 4. Install the "Windows Mixed Reality Headset” USB 3.0 connector to the on-board USB3.0 port. Install the "Windows Mixed Reality Headset” HDMI connector to the on-board HDMI port The Windows Mixed Reality Headset should work now. When the system boots up, press "F2" to enter UEFI setup screen. Download the driver from the following link: Z270 Gaming-ITXac/index.asp#os W1064 3. Answer: Requirements: O/S: Windows 10 Receiver / decoder: Onkyo TX-NR 747 or other receiver supports HDCP 2.2 Playback Software: Power DVD 14 (from Pioneer Ultra HD Blu-ray Drive) Configuration: M/B: Z270 Gaming-ITX/ac BIOS: P1.20 Setup: 1. Download the driver from the following link: https:// Z270 Gaming-ITXac/3. Please run "Ultra Blu-ray advisor” to see if all "Pass”. Put a 4K movie BD disc into the Pioneer Ultra HD Blu-ray drive. We have tested some memory modules on AM4 platform and users can refer to our suggested module list for choosing the finest ones to pair with your AM4 motherboard.